Starlink hardware guide
Starlink Standard Mounts: Wall, Pivot, Pipe, Ridgeline or Ground?
Quick answer:
Pick the mount by the surface you are fixing to, after you have confirmed your exact kit. For a Starlink Standard, Starlink's own guide points to the wall mount for a gable or fascia, the pivot mount for a shingled slope, the pipe adapter for a metal pole you already have, the no-drill ridgeline mount for a gable ridge, and the X-frame base for the ground. Every one exists to fix a sky-view problem, so check your view first.
Some links below are affiliate links: if you buy through them we may earn a commission at no extra cost to you. We only name real products and pick them for fit, not for payout.
A Starlink mount does one job: it puts the dish where it can see enough sky and keeps it there safely. That sounds simple, but mounts are model-specific and each one suits a different surface, so the mistake to avoid is buying by look or price. This guide sticks to the fixed-installation mounts for the Starlink Standard dish and takes its specifications from Starlink's public Standard accessories guide, checked on September 30, 2026. Specifications and compatibility can change, so confirm them on the shop listing for your kit before you buy.
Step 1: lock the exact dish model
The official guide lists its wall, pivot, pipe adapter, ridgeline and X-frame mounts as compatible with Starlink Standard 4, Starlink Standard 4 X and Starlink Enterprise. It also lists a separate Standard 4 to Standard Actuated mount adapter, meant for people who already have a mount installed for the older Standard Actuated kit and want to fit the newer dish without replacing it. If you are buying a new kit with no old mount, the guide recommends a mount designed for the Standard kit instead of that adapter. Starlink Mini and other kits use different accessories: our accessories guide covers those, and the dish comparison helps you confirm which kit you have or are buying.
The five fixed mounts side by side
Figures below are from Starlink's Standard accessories guide. Each kit includes 20 cable routing clips.
| Mount | Where it goes | Official limits | Drilling | Also in the kit |
|---|---|---|---|---|
| Wall mount | Exterior wall near the top of a gable or fascia | Fits an overhang of 4 in (about 100 mm) at most | Yes, 2 lag screws | Silicone; tools: drill, 6 mm bit, 9/16 in hex socket, level |
| Pivot mount | Slanted, shingled roof | Swivels to adjust angle and direction | Yes, 2 lag screws | 2 sealant tape squares and 2 sealant tape strips |
| Pipe adapter | An existing metal pole you already have | Pole diameter 31 mm (1.25 in) to 63.5 mm (2.5 in); metal only, not PVC or plastic | Attaches to the pole with an Allen key; no wall or roof fasteners in the kit | Allen key; the pipe is not included |
| Ridgeline mount | Top ridge of a gable roof | Metal or shingle roofs under 45° slope; not recommended for clay tile; wind rating up to 80 km/h (50 mph) | No, held by ballast | 4 ballast weights |
| X-frame base | Ground level, or a quick setup | Ground installation | Not needed by the kit; no fasteners listed | Mast adapter and mast |
You can browse these on Amazon, though availability of official accessories varies: wall mount, pivot mount, pipe adapter and ridgeline mount. Buy the one that matches your surface and your exact kit, not the cheapest in the list.
Choosing by surface
- Sky is clear from a gable end or fascia: the wall mount keeps the cable entry close and avoids the roof surface. Check the overhang first — the official limit is 4 in.
- Only the roof plane has a clear view and you are fine drilling: the pivot mount, with its sealant tape, is the official choice for a shingled slope.
- Renting, or you do not want holes in the roof: the ridgeline mount is the no-drill option. It needs a gable ridge, a slope under 45° and a roof that is not clay tile.
- A rigid metal pole is already there: use the pipe adapter, after measuring the pole (below).
- Nothing above ground blocks the view: the X-frame base gives a low, quick setup without touching the building.
Two calculations that save a wasted order
1. Will your pole fit the pipe adapter?
Measure the pole's outside diameter. If you only have a tape, wrap it round the pole, read the circumference and divide by 3.14: a 150 mm circumference gives a diameter of about 47.7 mm, which is inside the 31 to 63.5 mm range. Beware nominal pipe sizes. On standard steel pipe, a 1-1/4 in nominal pipe measures about 42.2 mm across, a 2 in pipe about 60.3 mm, but a 2-1/2 in pipe about 73 mm, which is too big for the adapter. Confirm on the listing whether Starlink's range refers to outside diameter, and remember it is for metal pipe only.
2. What does the ridgeline mount put on your roof?
The guide lists the mount at 5.8 kg (12.8 lb) and the ballast package at 25.3 kg (55.8 lb). Together that is 31.1 kg (about 68.6 lb) of package weight on the ridge, before you add the dish. The four weights would be about 6.3 kg each if they are equal; the guide gives only the total. If you are unsure the roof structure can carry that, or your area is regularly windier than 80 km/h (50 mph), ask a qualified installer instead of relying on the mount alone.
What you may still need to buy
Wall and pivot mounts list a drill, a 6 mm (1/4 in) bit, a 9/16 in hex socket, a marker and a level as recommended tools. If you do not own a socket set, a socket set is the usual purchase, and UV-resistant outdoor cable clips are worth having if you route a longer cable run than the included clips cover. Do not buy sealant or hardware to replace what a kit already includes without checking that it is suitable for your roof.
Before you drill or lift anything
- Check your sky view with the obstruction checker at the intended spot, not just from the ground.
- Confirm your exact dish and mount compatibility on the shop listing.
- Read our installation guide for cable routing, weatherproofing and when to hire a professional.
- Plan the cable length so the route is short and protected; see the accessories guide if you need a longer cable.
- Test the connection before and after moving the dish using the speed test.
This guide summarises manufacturer specifications; it is not engineering, roofing or electrical advice. Roof loads, wind and local building rules vary, so use a qualified professional for anything you are not sure is safe. Compare the whole hardware bill in the cost calculator and browse the rest of our Starlink buying guides.
Source: Starlink public Standard accessories guide (starlink.com/public-files/accessories_guide_standard.pdf), checked September 30, 2026. Pipe outside-diameter figures are standard steel pipe dimensions (ASME B36.10).
Don't just read — check your sky view.
Use the obstruction checker to reason through trees, rooflines, and other signal blockers around your dish.
Related tools
Recommended next steps
Obstruction Checker
Check trees, rooflines and sky-view blockers before you choose where to mount.
Starlink Speed Test
Test the connection before and after moving the dish to a new mount.
Cost Calculator
Add the mount and cable to your hardware total before you order.
Plan Picker
Match a Starlink plan to your location and use case.
FAQ
Which Starlink mount is best for a shingled roof?
Starlink's own accessories guide describes the pivot mount as designed for slanted, shingled roofs; it is fixed with lag screws and sealant tape. If you cannot or will not drill the roof, the ridgeline mount sits on the ridge of a gable roof and is held by ballast weights instead. It is meant for metal and shingled roofs with a slope under 45 degrees and is not recommended for clay tile.
Can I put Starlink Standard on a pole I already have?
Yes, with the pipe adapter, if the pole is metal and its diameter falls in the range Starlink lists: 31 mm (1.25 in) to 63.5 mm (2.5 in). Starlink says the adapter is only for metal pipe, not PVC or plastic, and the pipe is not included. Measure your pole first, because a nominal pipe size and its real outside diameter are not the same number.
Does the ridgeline mount need any drilling?
No. Starlink describes it as a no-drill mount that sits on the top ridge of a gable roof and is held in place by ballast weights. The weights are heavy: the guide lists the ballast package at 25.3 kg (55.8 lb) and the mount at 5.8 kg (12.8 lb), and gives a wind rating of up to 80 km/h (50 mph). Check that the roof can carry the load and that your local wind conditions fit that rating.
Is the same mount used for Standard 4, Standard 4 X and Enterprise?
According to Starlink's accessories guide, the wall, pivot, pipe adapter, ridgeline and X-frame mounts list Starlink Standard 4, Starlink Standard 4 X and Starlink Enterprise as compatible. Older Standard Actuated kits and Starlink Mini use different accessories, so confirm your exact kit before ordering.
Do I need a mount at all?
Not always. A mount exists to give the dish a clear view of the sky where the ground, deck or existing stand does not. Check your sky view first with the obstruction checker. If the view is already clear from a stable, safe spot, you may only need the ground-level X-frame base or nothing extra, and you should save the money you would spend on height.